Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Home Additions & ADU: The Dallas Owner’s Guide
If you’re planning a home addition or ADU in Dallas with KraftMaid cabinetry specified, you’re looking at a total project cost that typically runs $45,000 to $130,000 for the addition, with the cabinetry line item generally landing between $4,000 and $13,000 depending on the KraftMaid collection and linear footage. We install KraftMaid product daily across Dallas and stock the hardware, fillers, moldings, and touch-up kits that keep a big addition moving instead of stalling over a backordered hinge or missing corner block. The symptom picture is rarely dramatic: most Dallas owners don’t discover a KraftMaid issue until the cabinet doors start rubbing during the humid stretch from June through September, or a roll-out tray binds when the house settles on clay soil.
This page exists because a failed or missing KraftMaid part on an addition or ADU project has a cost far beyond the part itself: a kitchen island that can’t be finished, an inspection that gets pushed, a punch list that won’t close. You should know what we stock, what it costs installed, and whether the fix is a two-hour call or a re-order situation, before you pick up the phone.
Which KraftMaid Models This Applies To
KraftMaid builds cabinetry across several collections, and the hardware and trim specs shift between lines, so matching the correct part matters. The Vantage, Venicia, and mainstream KraftMaid collections all use different hinge platforms, different drawer box depths, and in some cases different hole-boring patterns. We’ve seen Dallas homeowners order a hinge set online for a Vantage door and discover the mounting plate is 6mm taller than the cutout allows: the door hangs proud by a visible gap, and the reveal looks like a first-year apprentice installed it.
The fastest way to identify the right KraftMaid part in Dallas is the small printed label inside the cabinet door or drawer box, which carries the cabinet line, finish code, and order number, assuming a previous painter didn’t sand it off, which happens more than you’d think. If the label is gone, we measure the cup diameter, hinge arm type, and reveal, because KraftMaid’s metric-spec hardware does not swap cleanly with big-box equivalents, even when both look like ordinary concealed hinges at a glance. For most Dallas additions, OEM KraftMaid parts are the right call when finish and fit must match; there are solid aftermarket equivalents for soft-close mechanisms and roll-out tray slides, but we tell homeowners up front which path makes sense, because good aftermarket saves money and bad aftermarket costs you a callback.
Styles & brands we work with
Signs Your KraftMaid Home Additions & ADU Is Failing
- Doors that drifted out of alignment. Dallas clay soil shifts, and a new addition settles more in the first two summers than homeowners expect. When the wall moves half a degree, KraftMaid doors and drawer faces show it first as uneven reveals and corners that catch.
- Soft-close mechanisms that slam or don’t catch. The small hydraulic pistons on KraftMaid hinge sets wear predictably, especially in high-use kitchens in ADU rental units. We replace these by the dozen across Dallas, often during the same visit as the original service call.
- Roll-out trays that bind on one side. The tray slide brackets can loosen or the slides themselves accumulate enough dust and construction debris during a remodel to grind. A tray that fights you halfway out is a hardware problem, not a strength problem.
- Drawer boxes that rack or separate at the corner joints. KraftMaid’s dovetail construction is durable, but a drawer front that has pulled from the box, usually from a child standing on an open drawer or one overstuffed drawer in a rental kitchen, needs a repair plate or a replacement box, not a screw driven in at an angle.
- Finish wear at the sink base on a Dallas addition. The humidity swings in Dallas mean the cabinet under the sink sees more moisture than the rest of the kitchen combined. Blistering or delamination there is often the first finish failure, and swapping the sink base door or adding a vent can stop a full replacement.
Replacement Cost & What’s Included
For KraftMaid parts work within a larger Dallas addition or ADU project, our installed pricing typically breaks down like this:
- Single cabinet door or drawer front replacement: $80 – $250 installed, depending on finish and whether the part is stock or made-to-order from KraftMaid
- Full hinge swap on a bank of doors (soft-close retrofits): $180 – $500 installed, hardware included
- Roll-out tray slide replacement or repair: $120 – $350 installed per cabinet, including the tray inspection
- Sink base door replacement with moisture-rated upgrade: $150 – $400 installed
- Full KraftMaid cabinetry install as part of an addition: $4,000 – $13,000 depending on linear feet, collection, and crown/trim detail
Every quote from Mason Remodeling Co Dallas is a written price before any work starts, with parts and labor separated so you can see exactly what the KraftMaid component costs versus our time to install it. The workmanship is covered by our 365-Day Done Right Promise: if an install isn’t right within a year of completion, we make it right at no cost to you.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Most KraftMaid cabinet hardware replacement is not dangerous, but it is precise, and the precision is where Dallas homeowners lose money. You can safely tighten a loose hinge screw, clean out a debris-clogged slide, or confirm which door is out of alignment with a level and a flashlight. What we don’t recommend doing yourself is ordering parts off a part number you found on a forum, because KraftMaid revisions mean a part number from three years ago may not match your specific cabinet. The wrong hinge installed anyway means a door that scrapes, a return trip to the post office, and a cabinet that now has two sets of screw holes where one set was supposed to be. If you’d rather not gamble, call Mason Remodeling Co Dallas at (432) 302-8761 and we’ll identify the exact part, bring it with us, and install it the same visit.
FAQs
KraftMaid cabinetry in Dallas typically lasts 20 to 30 years with the hardware needing replacement every 8 to 12 years, depending on use and humidity exposure. ADU rental kitchens on the short-term market wear hinges and slides faster than a single-family home because the usage cycle never stops. Call (432) 302-8761 if your cabinets are showing their age and you want an honest read on repair versus replacement.
Some KraftMaid parts repair well: loose hinges can be tightened with a fresh screw or a thread insert, and drawer fronts can be reattached with repair plates. Hydraulic soft-close mechanisms cannot be rebuilt; they’re sealed units meant to be swapped. Call us and we’ll tell you which path is cheaper before you spend anything.
A typical KraftMaid hardware repair or replacement takes one to two hours on site if we have the part with us, which we do for the most common hinge sets, slides, and soft-close parts. Custom-finish doors ordered from KraftMaid take two to four weeks to arrive in Dallas, and we’ll tell you that timeline before you commit. Call (432) 302-8761 and we’ll give you a straight answer on timing for your specific cabinet.
Our Dallas trucks stock the most frequently needed KraftMaid hardware: soft-close hinge sets, mounting plates, drawer slide brackets, and repair plates in white, gray, and natural finishes. For finish-matched doors, drawers, and trim, we order directly through KraftMaid’s system, which means the part matches exactly but takes two to four weeks. Call (432) 302-8761 and we’ll check stock before you schedule.
Call Mason Remodeling Co Dallas for KraftMaid Parts and Installation
Mason Remodeling Co Dallas is an independent service provider and not affiliated with KraftMaid; we’re just the crew in Dallas that installs and services more of their product than most, including Cambria, Silestone, and Kohler alongside. You should know who is coming, what it costs, and what happens if something goes wrong before we ever pick up a tool. When you call (432) 302-8761, a live person answers, and Isaac Pruett or a member of his crew will get you a written price for your KraftMaid repair or install, free of charge, before any work starts.
Written by Isaac Pruett, Owner, Mason Remodeling Co Dallas at Mason Remodeling Co Dallas, serving Dallas and nearby areas.
