Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Blanco Fence Installation: The Dallas Owner’s Guide
Blanco fence installation in Dallas typically runs $3,500 to $9,000 for a complete project, depending on the fence style, total linear footage, and whether we’re working with existing posts or setting new ones. Most Blanco-compatible fence installations in the Dallas area take two to four days from first post hole to final gate adjustment. You’ll usually notice the problem as a sagging gate, a post that’s leaning after a storm, or pickets that have started pulling loose from the rails, and by the time it’s visible, the real issue is often below the soil line or inside the hinge hardware.
We’re an independent Dallas contractor, not affiliated with Blanco, but we work with their fence systems regularly because Dallas homeowners keep them on their properties and the parts are still readily available. What we’ve learned from installing and repairing Blanco fencing across neighborhoods from Oak Cliff up through the design districts is that the failures are predictable: post rot at grade level, hinge brackets that loosen in Texas heat cycles, and gate frames that twist when the clay soil shifts. None of it is exotic, but all of it needs to be addressed before a gate falls off its hinges and takes part of the fence with it.
Which Blanco Models This Applies To
Blanco fence products in the Dallas market fall mostly into two lines: the Blanco Classic series, which uses 2×4 framed panels with pressure-treated rails and cedar or pine pickets, and the Blanco Contour series, built with galvanized steel post inserts and heavier gate hardware. If you still have the original paperwork, the model tag is usually stapled to the inside of the gate frame or printed on a sticker under the top rail. If that’s gone, which is most of the time after a few Dallas summers, we identify the series by measuring the post spacing and the gate frame thickness: Classic posts sit at 6 feet on center with 1-3/8-inch top rails; Contour posts sit at 8 feet with 2-inch rails and a much sturdier corner bracket.
The OEM versus aftermarket call for Blanco fencing depends on what we’re replacing. For structural posts and gate frames, we recommend Blanco OEM parts or a structural equivalent that matches the post gauge exactly, because a lighter-gauge aftermarket post will develop the same lean within two years. For pickets, hinge brackets, and latch hardware, quality aftermarket parts from the same suppliers we use for other brands perform just as well and often cost 20 to 30 percent less. One Blanco-specific gotcha: the Contour series hinge brackets are drilled on a diagonal bolt pattern that doesn’t match most universal hardware, so if you order the wrong replacement hinge online, the holes won’t line up and you’ll end up drilling the gate frame, which weakens it. That’s the kind of mistake we see on repair calls in Dallas about once a month.
Styles & brands we work with
Signs Your Blanco Fence Installation Is Failing
- Gate drags or won’t latch. The gate frame has twisted, usually from a loose hinge bracket or a post that started leaning after Dallas clay soil expanded during a wet spring. The latch plate and striker no longer meet square, and forcing the latch closed just bends the hardware further.
- Post leans at the base. Water has been pooling around the post, and the below-grade portion is rotting or the concrete footing has cracked. In Dallas, this is most common on the north side of fences where shade keeps the soil damp longer after rain.
- Pickets pulling away from rails. The fasteners have corroded or the rail itself has warped from repeated wet-dry cycles. Once one picket goes, the neighbors follow because the rail loses its rigidity and every wind gust works the remaining nails loose.
- Gate frame splitting at the hinge screws. The original screws were too short or the wood has dried and split around them. This is a Classic-series problem more than Contour, and it will eventually tear the hinge completely out of the frame.
- Fence section sags between posts. The top rail has bowed or a post has settled. In Dallas’s expansive clay soil, posts will settle unevenly, and a once-straight fence line starts to look like a rolling wave.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a Blanco fence installation in Dallas, you’re looking at $3,500 to $9,000 installed, and the range comes down to three things: how many posts we’re setting new versus reusing, the total linear footage of the run, and whether the gate gets rebuilt with a new frame and hardware or just re-hung. A straightforward replacement of posts, rails, and pickets on a typical Dallas backyard run of 60 to 80 linear feet with one gate usually lands between $4,000 and $6,500. Longer runs, Contour-series hardware, double gates, or fence removal and haul-off push toward the higher end.
Every quote is a written line-item price before we start, so you’ll see the post cost, the panel and picket cost, the gate hardware cost, and the labor separated out. There are no verbal estimates that grow later, and no change orders unless you ask us to expand the scope. The workmanship is covered by our 365-Day Done Right Promise: if anything we set, hung, or fastened fails within a year, we come back and fix it at no charge. You should know who is coming, what it costs, and what happens if something goes wrong before we ever pick up a tool.
DIY or Call Us?
If a post is leaning, you can safely dig around the base and check whether the footing is cracked or the wood is soft at grade level, that’s useful information when you call, and it won’t hurt anything. Replacing a picket or two is also within reach for a handy homeowner. But resetting a post, re-hanging a gate, or rebuilding a gate frame is where DIY projects in Dallas tend to go sideways, because the ground doesn’t cooperate: you’ll hit a clay layer that fights the dig, then the new footing won’t set level, and the gate still drags. A gate that falls off its hinges is a couple hundred pounds of wood and steel, and we’ve repaired fences where a DIY gate came down on a car or a kid’s playset. This is one part where it’s cheaper in the long run to have it done right the first time. Call us at (432) 302-8761 and we’ll walk the fence with you and give you a written number.
FAQs
A properly installed Blanco fence in Dallas should last 15 to 20 years with pressure-treated posts and quality pickets, though gates and hardware typically need attention at the 7-to-10-year mark due to heat and humidity cycling. Call (432) 302-8761, and we’ll give you an honest read on what’s left in your existing fence.
Yes, in most cases we can replace individual posts, sections, or the gate without redoing the whole fence, as long as more than half the posts are still sound and the rails haven’t rot across the run. Call (432) 302-8761 and we’ll tell you what’s repairable and what’s not before any money changes hands.
A typical Dallas Blanco fence installation with one gate takes two to four days, including post setting, panel building, and final gate adjustment, depending on weather and how much old fence needs to be removed. We’ll give you a schedule in the written quote and hold to it.
We keep common Blanco-compatible parts on the truck for Dallas service calls: hinge brackets, latches, post caps, pressure-treated posts, and gate frame stock, and Contour-series hardware is usually available from our Dallas suppliers within one business day. Call (432) 302-8761 and we’ll confirm the part is in hand before we schedule the work.
Written by Isaac Pruett, Owner, Mason Remodeling Co Dallas at Mason Remodeling Co Dallas, serving Dallas and nearby areas.
