Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ActiveYards Fence Installation: The Dallas Owner’s Guide
ActiveYards fence installation in Dallas typically runs $3,500 to $9,000 for a full perimeter or significant section, depending on linear footage, gate count, and whether we’re matching an existing product line the homeowner already owns. We install and repair ActiveYards-compatible fencing, including the Classic, Grand, and Providence series, and we can usually get a crew to your property the week you call. Most owners discover they need us when a North Texas storm snaps a post at ground level or the gate stops latching after the clay soil shifted one too many times.
ActiveYards builds aluminum and vinyl fencing systems engineered for modular replacement, which means a failed section rarely requires tearing out the whole run. That said, the specific product line matters. A Grand series panel won’t drop into a Classic series frame without modifying the post channels, and we’ve seen more than a few weekend warriors learn that the hard way. If you’re looking at a failing section, sagging gate, or a post that moves when you push it, here’s what to know before you spend a dollar.
Key takeaways:
- Full ActiveYards fence installation in Dallas: $3,500 – $9,000 installed
- We stock common ActiveYards-compatible profiles and hardware on our trucks
- Most failures in Dallas come from clay soil movement and wind load, not product defects
- You get a written price before work starts and the 365-Day Done Right Promise
Which ActiveYards Models This Applies To
The first thing to know: ActiveYards changed their post-mounting design between the older Classic rounds and the newer square-post Grand and Providence lines. If you have the square-post system, your options for matching parts are broader because the current channel and bracket design is modular across Grand, Providence, and the privacy line. If you have older round-post Classic, you’ll want us to verify the panel width and picket profile before ordering anything, because a few of those profiles are discontinued.
To identify what you have, look for an engraved or stamped series name on the bottom rail of a panel, or measure the picket width. Classic pickets run around 5/8 inch wide with a rounder profile, while Grand pickets are flatter and wider at 7/8 inch. The difference matters: a Grand picket won’t seat cleanly in a Classic bottom rail channel. Here’s what your ActiveYards line tells us about part availability:
- Classic Series (round-post, narrower pickets): Many panels still available; some post caps and gate hardware discontinued. We match where possible and retrofit where not.
- Grand Series (square-post, 7/8-inch pickets, beefier rails): Best parts availability. This is the line we install most across Dallas and can source quickly.
- Providence Series (updated aluminum, hidden fastener look): Growing in DFW installations. Compatible with current hardware kits but requires Series-specific post caps.
- Vinyl lines (ActiveYards privacy and semi-privacy): Post sleeves and bottom rails are the usual failure points in heavy clay. We carry matching white and tan profiles.
OEM versus aftermarket: ActiveYards-branded panels are the cleanest match on a 10-year-old fence where UV exposure has faded the finish. A quality aftermarket picket may be functionally identical in a fresh run but can catch the light differently against older aluminum. For Dallas specifically, the bigger decision is usually steel versus aluminum post reinforcement. In expansive clay, we recommend concrete footings at 24 inches minimum with gravel drainage at the base, because standing water at the post collar is what rots vinyl sleeves and seizes aluminum post channels.
One compatibility gotcha we run into regularly: ActiveYards gate hinges are Series-specific. The Grand-series hinge plate spacing does not align with the Classic-series frame, and forcing it just elongates the screw holes until the gate sags for good. We stock the right hinge kits for both major lines on the truck, which saves a second trip.
Styles & brands we work with
Signs Your ActiveYards Fence Installation Is Failing
- The gate drags or won’t close. In Dallas, this is almost always soil movement: the post collar settles, the gate hinges pull misaligned, and the latch bar stops meeting the strike. If the gate is over 6 feet wide, the frame itself may be torquing under its own weight.
- Posts lean or wobble when you grip and shake them. Clay soil expands and contracts with our wet-dry cycles, which loosens even well-set posts over time. A wobbling post is not a surface problem; it means the footing is failing below grade.
- Pickets crack at the top or bottom rail. Aluminum expands and contracts in Texas heat, and vinyl UV-blazes faster than manufacturers’ ten-year warranties suggest. Cracks at the rail channel indicate the panel was installed too tight for Dallas’s 100-degree summer expansion cycles.
- Rust staining at post bases or gate hardware. ActiveYards aluminum does not rust, but the galvanized internal steel stakes and brackets do, especially where irrigation overspray hits the base. Staining means moisture has been sitting there long enough to corrode the reinforcement.
- Bottom rails bow upward or section seams pull apart. When wind load combines with loose posts, panels flex along their weakest point: the bottom rail channel. You’ll see the seam gaps grow wider over a matter of months, not years.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a typical Dallas residential lot, ActiveYards fence installation runs $3,500 to $9,000 installed. A single section repair or gate rebuild usually falls on the lower end of that range, while a full perimeter with two gates on a standard 60-foot-deep lot lands mid-to-upper. Here’s the breakdown we give every homeowner before work starts:
| Scope | Typical Dallas Price |
|---|---|
| Single section replacement (6 – 8 foot panel, post, hardware) | $350 – $900 |
| Gate rebuild with new hinges and latch | $500 – $1,400 |
| Post reset or replacement (concrete footing) | $275 – $600 each |
| Full perimeter install (150 – 250 linear feet, one to two gates) | $3,500 – $9,000 |
Those numbers include materials, labor, removal and haul-off of old sections, and leveling the new run to your yard’s grade. What drives the range: linear footage, gate sizes, condition of remaining posts, and whether you want vinyl or aluminum. Every quote is written and itemized before we start, with no change orders that appear like mushrooms after a rain. If the work is not right within 365 days of completion, we make it right at no cost. That’s the Mason Remodeling yardstick, and Isaac Pruett holds us to it on every job.
DIY or Call Us?
A fence panel swap is not in the same danger class as a garage-door spring or a live electrical panel, but ActiveYards products are built for modular replacement, not casual improvisation. You can safely check the obvious: where the gate is binding, whether posts are plumb, which pickets are cracked. You can tighten hinge screws and clear grass away from the post bases. What you should not do is pry a panel out of its post channel with the gate still hanging on that post, or try to reset a leaning post without pulling the concrete and checking for a broken internal steel stake. A 60-pound aluminum panel under tension can shift faster than you expect.
Where DIY usually goes wrong on ActiveYards specifically: homeowners buy the wrong series panel online, drill new mounting holes, and turn a $600 section replacement into a whole-line retrofit. If you’re not sure what you’re looking at, call us at (432) 302-8761. We’ll walk you through identifying your series, tell you what we’d charge, and if you want, show you the written estimate before anything gets scheduled. No obligation, no pressure.
FAQs
An ActiveYards aluminum fence properly installed on concrete footings will last 25 to 35 years in Dallas; the powder-coat finish typically shows UV dulling after 10 to 15 years of Texas sun, but the structure holds. Vinyl ActiveYards lines generally deliver 15 to 25 years before post sleeves start showing heat and soil-stress cracks. Concrete footing depth and drainage at the post base extend life more than any other factor. If you want a specific read on your existing fence, call (432) 302-8761 and we’ll tell you what we’d do to get the most years out of it.
Usually yes. A cracked picket, a loose bottom rail, or a gate that needs hinge replacement can be repaired without pulling the whole section. The tipping point is post integrity: if the post is leaning or the internal steel stake is rusted through, that post needs replacement, and the adjacent section work usually follows. We’ll always give you the repair price and the replacement price side by side so you can decide with numbers, not guesswork.
Most full-perimeter ActiveYards installations in Dallas take two to four working days from post dig to final gate adjustment. A single-section replacement or gate rebuild is typically a half-day job. Weather can shift that schedule, especially during spring storm cycles when the ground is saturated, but we give you a written time frame with the estimate and keep you posted if anything changes. Call (432) 302-8761 to lock in a timeline for your specific scope.
We keep the most common ActiveYards-compatible profiles, post caps, hinge kits, latch bars, and bottom rail channels on our trucks. Unusual colors or older Classic-series pieces occasionally need a quick order, but most Dallas repair calls are completed the same visit. We also stock parts for KraftMaid, Cambria, and Silestone on the remodeling side, so our crews show up prepared rather than running to the supply house mid-job.
Written by Isaac Pruett, Owner, Mason Remodeling Co Dallas at Mason Remodeling Co Dallas, serving Dallas and nearby areas.
