Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Belgard Fence Installation: The Dallas Owner’s Guide
Belgard fence installation in Dallas typically runs $3,500 – $9,000 for a complete post-and-panel run, depending on linear footage, gate hardware, and whether we’re replacing failed posts or starting fresh. Most homeowners land on this page because a post has gone soft at the base, a gate has started dragging, or a panel cracked after a freeze-thaw cycle. We stock Belgard-compatible posts, panels, gate kits, and hardware, and in most Dallas neighborhoods we can have a crew out for measurement within a couple of days.
What we see most often in Dallas isn’t the panel itself failing. It’s the post. The freeze-thaw swings we get in January and February, followed by the clay-heavy soil in places like Lake Highlands and Richardson, work on the post base until it tilts or cracks. That tilting post is the part you notice first, and it’s usually the one that decides whether you’re replacing a section or the whole fence line.
Which Belgard Models This Applies To
Most Belgard fence work we do in Dallas falls into three lines: the Metro collection (modular post-and-panel, the most common we see in newer builds), the Bel Air collection (a taller, more traditional privacy fence), and the Melville post-and-panel system often paired with Belgard hardscape walls. The part you need depends on which system was originally installed, and here’s the compatibility gotcha: Belgard fence panels are not universally interchangeable across collections. A Metro panel will not drop into a Bel Air post channel. The post profiles and channel widths differ by as much as 3/8 inch. If you’re not sure which system you have, look for a small molded font on the inside face of the post cap or near the bottom rail of a panel. If there’s no marking, take a photo of the post cross-section and we can usually identify it from that.
We install OEM Belgard replacement parts on warranty or appearance-critical work. For out-of-production colors or homeowner budget cases, we can source a quality aftermarket post sleeve or panel insert that matches the reveal line, though we’ll always tell you the difference in writing before you commit. Mason Remodeling Co Dallas is an independent service provider, not affiliated with Belgard, but we order their parts direct from specification-grade distributors so you’re not waiting on a big-box special order.
Styles & brands we work with
Signs Your Belgard Fence Installation Is Failing
- Post lean or drifting at the top. The base has lost enough bearing in the soil to shift, usually after a wet winter in Dallas clay. The fence won’t fall tomorrow, but it will keep moving, and a leaning post puts continuous stress on the panel channels.
- Gate scraping or failing to latch. If the gate side used to clear and now drags, the hinge post is moving, or the gate frame has racked. On Belgard gates, the frame is usually aluminum inside the composite post, and the scrape you hear is the gate rubbing the post cap channel.
- Cracked panel or spider lines in the finish. Composite and polymer panels can crack at the bottom corner near the post channel. Texas sun is brutal on the older panel generations, and thermal expansion against an over-tightened channel is the usual cause.
- Post cap lifted or cracked. Water gets in through the top, then freezes. You’ll see a cap that’s pushed up off the post by a 16th or even an 8th of an inch.
- Soft or mushy soil at the post base. If the ground around the post feels spongy after rain, you’ve got drainage running along the fence line. That’s a repair-or-relocate decision, not just a post swap.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Dallas, a straight post replacement with new concrete footing and panel reset runs $350 – $600 per post on most Belgard systems. A full panel section replacement runs $80 – $150 per linear foot for standard Metro or Bel Air height. A complete fence installation of 50 to 60 linear feet with a single pedestrian gate lands in the $3,500 – $9,000 range we lead with, and that’s parts, labor, disposal of the old section, and the concrete work.
What drives the range is three things: the collection (Bel Air panels cost more per foot than Metro), the number of posts that need concrete work rather than just panel swaps, and whether a gate needs to be rebuilt on the same hinge geometry. We give you a written price before any work starts, with parts and labor split out line by line. No change orders unless the ground opens up and we find something genuinely hidden.
Every completed job carries our written guarantee for 365 days from the completion date. If a post shifts, a panel cracks at the channel, or a gate stops latching within that window, we come back and make it right at no charge.
DIY or Call Us?
Here’s the honest split. You can clean debris out of the post channels, check for a lifted cap, and photograph the post base so you’re not describing the problem blind on the phone. Those are useful, safe checks. What you should not do on a Belgard fence is dig out a concrete footing by hand in Dallas clay and try to reset a post. If the post is load-bearing for a gate, you’re dealing with real tension and an unpredictable pivot point. A post that lets go mid-extraction can swing the whole panel section into whoever is standing nearest.
Isaac Pruett walks every fence job himself before the first post is pulled. He grew up in Los Angeles and learned the trade at Los Angeles Trade-Technical College, running jobs across Southern California before bringing the same methodical approach to Dallas, where he’s worked steadily from Oak Cliff to the design districts near the Dallas Market Center. He still checks alignment with a string line because he learned early that a plan on paper and a house in front of you are two different things. If you’d rather not spend your Saturday fighting a post that doesn’t want to let go, call us at (432) 302-8761 and we’ll get you on the schedule.
FAQs
A properly installed Belgard fence in Dallas lasts 20 to 30 years on the panels, with posts needing reset or replacement around the 12 to 15 year mark in our clay-heavy soil. Direct sun on a west-facing run will fade color faster and can shorten the cosmetic life of older panel generations, but structural life holds up if the post footings are deep enough. Call (432) 302-8761 and we’ll come look at your specific line and orientation.
If the post hasn’t cracked and the lean is under about 10 degrees, we can sometimes backfill, re-compact, and brace it in place, but in Dallas clay that repair typically lasts only a couple of seasons. A cracked or soft post should be replaced rather than patched. We’ll tell you which applies before you spend a dollar, with a written price either way.
A single post replacement takes half a day, including concrete set time with a fast-setting mix. A full panel section between two healthy posts takes one to two hours. A complete 50 to 60 foot fence with a gate is usually a two-day job in Dallas, with day one for demolition and footings and day two for panel and gate installation. We’ll put the schedule in the written quote before work starts.
We stock the most common Metro and Bel Air panel profiles, post sleeves, caps, and gate hardware in our Dallas shop, and we can have less common Melville or out-of-production colors from our distributor within a week. If we don’t have your exact part on the truck the first day, we’ll tell you that before we schedule, not after we’ve dug a hole. Call (432) 302-8761 and we’ll check stock while you’re on the phone.
You should know who is coming, what it costs, and what happens if something goes wrong before we ever pick up a tool. That’s how we run every job at Mason Remodeling Co Dallas. Call (432) 302-8761 for a free estimate, and we’ll put the price in writing.
Written by Isaac Pruett, Owner, Mason Remodeling Co Dallas at Mason Remodeling Co Dallas, serving Dallas and nearby areas.
