Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Dallas Owner’s Guide
Jerith fence installation in Dallas typically runs $3,500 to $9,000 installed, depending on the fence line length, gate count, and whether we’re pulling old posts or setting new ones. We stock Jerith-compatible aluminum and steel posts, gate hardware, and panel brackets on our trucks, so most replacement calls get resolved in a single visit. Most Dallas homeowners call us after a windstorm torques a gate post or after years of black clay soil movement has pushed a post out of plumb, leaving the gate dragging or the panels racked. You notice it as a gate that won’t latch without hip-checking it, or a fence section that leans like it’s had a long week.
Which Jerith Models This Applies To
Jerith manufactures residential and light-commercial aluminum and steel fence systems, and the install methods we use apply to their most common Dallas product lines: the Estate, Coventry, Laurel, and Baron series. The compatibility gotcha we see constantly is post size. Jerith gates swing on either 2-inch or 2.5-inch square posts, and panels hang on posts that can be 2-inch, 2.5-inch, or 4-inch depending on the series and height. You can’t swap a 2-inch hinge post for a 2.5-inch without changing the gate hinge plates and the panel brackets. If you’re unsure what you have, look at the post cap or the inside face of the gate frame for a stamped model number, or measure the post width across the flat with a tape measure. That number tells us what’s on the truck before we roll out.
Jerith uses aluminum posts with a baked-on polyester powder coat, which holds up against Dallas heat far better than wet-spray paint, but the coating is thin at the gate hinge mounting points. That’s where corrosion starts. For hardware, we carry Jerith OEM hinge sets and latch assemblies, plus quality aftermarket replacements from comparable aluminum extrusion suppliers when a discontinued color or older series makes OEM impossible to source. We’ll tell you which one we’re quoting and why before you spend a dollar.
Styles & brands we work with
Signs Your Jerith Fence Installation Is Failing
- Gate post leaning at the top. In Dallas’ expansive clay soil, the ground swells when wet and shrinks when dry, and a post set in a shallow concrete collar will walk out of plumb over three to five seasons. The hinge side drops, the latch side rises, and the gate starts catching.
- Gate dragging or scraping the ground at the swing end. Almost always a hinge post that’s shifted, not a bent gate frame. Jerith gates are light enough that hinge wear shows up as sag before the frame bends.
- Latch won’t catch or requires a shove. The spring-loaded latch on many Jerith gates relies on the two posts being parallel and square. Once the post moves a half-inch, the striker plate lands in the wrong place and you’re down to bungee cords.
- Panels rattling in the wind or popping out of the brackets. The black plastic or nylon bracket inserts Jerith uses to secure panels to posts degrade under North Texas sun and get brittle after six to eight years.
- White chalky residue on posts or brackets. That’s the powder coat breaking down at stress points, and in Dallas humidity it leads to pitting and eventual structural thinning at the base of the post.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Dallas, most Jerith fence installation jobs we quote land between $3,500 and $9,000. The range depends on three things: linear footage of fence line being reset, how many gate posts need to be re-set in fresh concrete, and whether we’re keeping your existing panels or swapping in new ones to match the repaired sections. A simple two-post gate reset with new hinges and latch hardware usually sits at the low end. A full yard line of 150 feet with three gates, new posts, and panel re-hang sits higher.
Every quote includes labor, concrete for post footings, hardware, haul-off of old materials, and a written line-item price before any work starts. That’s Mason Remodeling Co Dallas policy, and it’s Isaac Pruett’s policy too: you get the exact number on paper, not a verbal range that grows on the final invoice. Our 365-Day Done Right Promise covers the installation: if anything we set or hung fails within one year of the completion date, we come back and make it right at no charge.
DIY or Call Us?
You can safely check the obvious things yourself: wiggle each post and see which ones move, check whether gate hinges have visible slop when you lift the gate by the latch end, and note whether the panels are still seated in their brackets. What you should not do is dig out a leaning post and try to re-set it without knowing your Dallas soil type and frost line. The clay here doesn’t hold a post the way sandy loam does, and a post set in a too-shallow hole with a too-small concrete collar will lean again by the next wet spring. That’s a $300 fix that turns into a second $900 repair. If your Jerith fence is moving, call (432) 302-8761 and we’ll give you a straight answer on whether it’s a reset, a re-hang, or a full section replacement, and what each option costs.
FAQs
A properly installed Jerith aluminum fence with posts set 30 to 36 inches deep in concrete will last 25 to 30 years in Dallas, though gate hardware and bracket inserts typically need replacement around year eight to ten due to sun exposure and soil movement. Call (432) 302-8761 if you want us to assess your specific fence line.
Yes, if the post itself is still straight and the powder coat isn’t compromised, we can dig out the old footing, re-set the post in new concrete at the correct depth, and re-hang the gate, usually in one day. If the post is bent or corroded at the base, replacement is the honest call.
A single gate post reset and re-hang takes four to six hours including concrete cure time to the point the gate can hang, and we usually complete a full two-post gate reset same day. Full fence line re-installs with multiple posts take two to four days depending on footage.
We stock common Jerith post sizes, panel brackets, hinge sets, and latch hardware on our trucks, so most repairs don’t require a parts order. If you have an older Jerith series with discontinued colors, we’ll source the closest matching aftermarket equivalent and show you a sample before installing it.
Call Mason Remodeling Co Dallas at (432) 302-8761 for a free estimate on Jerith fence installation. You’ll get a written price before any work starts, the name and photo of the technician before they arrive, and a one-year guarantee on the work.
Written by Isaac Pruett, Owner, Mason Remodeling Co Dallas at Mason Remodeling Co Dallas, serving Dallas and nearby areas.
